Converting a Sears Kenmore into a "Kegmore"
Firkin Around...the garage.
Here's my old beer fridge, which you may remember from a previous post. I have begun to homebrew, therefore the refrigerator needed to come up to the next level, since I also chose to keg the beer instead of bottling. This system is setup for a ball lock style corny (Cornelius) keg, but you may get parts for your own pinlock or Sankey style connections.
Below is a photo step-by-step on how the conversion was accomplished.
Project cost: Approximately $300 (assuming you already have the donor fridge)
Parts & Tools list:
 |
| Kenmore is now a Kegmore |
- 1" metal cutting hole-saw and a 1/8" metal bit
- Round or half round, metal file
- Beer faucet, shank and faucet wrench
- 6' of approved gas tubing, 1 gas ball lock connector and two hose clamps
- 6' of approved food grade tubing, 1 liquid ball lock connector and two hose clamps
- 1 five pound CO2 canister and a CO2 regulator/gas gauge
- 1 Corny keg
- 1 stainless steel drip tray
Acquiring the parts:
I purchased the keg from an online store. Just search for "corny" or Cornelius kegs. I shopped for the lowest price and found new kegs (made in India) for $113 w/free shipping. It uses all the same parts as American made corny kegs, so it will be easy to get spare parts like the dip tube, gas tube, springs, gaskets and poppets. Some are also made in China and Italy as the US does not seem to manufacture these style kegs any longer. I have seen them in 5, 3 and 2.5 gallon sizes (brand new), and there are plenty of US made 5 gallon used cornys still out
there if you are on a budget.
there if you are on a budget.
The drip tray was also available online and cost about $20.
 |
| Everything here was $150 and in one kit |
I did not have a 1" metal hole-saw, so add another $25 for a set of saws. If you, or someone you know, owns a 1" saw, you can save the $$$ for more beer! Lucky you.
As mentioned before, I have the fridge and was willing to drill some holes. If you don't have a refrigerator, scour the local want-ads or Craigslist in your area. You should be able to pick up a decent working fridge for around $100 or less.
Start by selecting a flat location with adequate access inside the fridge door. I had considered mounting the taps on one side of the fridge, but after placing my hand on the sides while the compressor was running, I discovered a few warm spots (to the touch) by running the palm of my hand along the outside skin of the unit. This indicates that some coils may be present as part of the defrosting or cooling system. Even if it is cool to the touch, there may be unseen wiring buried between the metal exterior and the plastic/insulation interior. Since the door has none of these issues with which to contend, it made the choice easy. I'd recommend the side closest to the hinge, if accessible, as this will keep the beer line hoses out of the way when the door is opened and closed.
Start by selecting a flat location with adequate access inside the fridge door. I had considered mounting the taps on one side of the fridge, but after placing my hand on the sides while the compressor was running, I discovered a few warm spots (to the touch) by running the palm of my hand along the outside skin of the unit. This indicates that some coils may be present as part of the defrosting or cooling system. Even if it is cool to the touch, there may be unseen wiring buried between the metal exterior and the plastic/insulation interior. Since the door has none of these issues with which to contend, it made the choice easy. I'd recommend the side closest to the hinge, if accessible, as this will keep the beer line hoses out of the way when the door is opened and closed.
Safety glasses on, begin by drilling a 1/8" hole on the inside of the door, all the way through to the outside, remembering to keep the bit level. The outside hole will act as a pilot marker for the hole-saw. Switch over to the 1" hole-saw and repeat the process. Start by cutting a 1" hole into the plastic & insulation until the pilot bit "finds" the 1/8" pilot hole, then stop. Remove the debris from the hole-saw, then place the pilot in the outside door hole and finish cutting the hole. Drill slowly and carefully each time.
Note: There is enough room in the utility door to add two more taps, right and left of this one. I planned the placement for that possibility.
I had to pull out the two lower crisper bins and shelf to allow enough head space for the corny keg with the ball lock connectors attached. As you can see, there is still plenty of room in the door and on the adjustable shelves for beer or food. I like to keep a few chilled (never frozen) glasses in the door. Just place a rubberized drip shelf to allow them to stay clean and ventilated.
Down the road, a board will be added to keep the CO2 tank and keg level in the bottom of the fridge.
Center, mark and drill the holes for the drip tray. Be sure to check the height of the tray to the tap so you have clearance. Use your judgement for best positioning.
Top Tip: Later, I will add a drain to my drip tray, attach some tubing, running the line back through the door and into an empty gallon jug. It will act as a runoff drain. I would place the jug in the lower part of the inside door. Great for party guests that have an occasional oops, without having to frequently sponge out the bottom of the tray.
Cool firkin project!
